Hydromatic Pumps

KEY FEATURES:

• Oil Filled Motors - Cooler operating than air filled motors and continuous lubrication of the bearings for longer life
• Slip Fit Stators - For easy of service
• Seal Cord Entrance - Triple seal protection, prevents moisture entry for longer life.

• Available configurations, rails and accessories:
  • Rail Systems Available
  • Controls and Accessories Available

KEY FEATURES:

• SEPTIC TANK EFFLUENT
• HIGH HEAD SUMP DEWATERING
• 3/4" SOLIDS HANDLING

GENERAL DATA:

DISCHARGE: 2"

OPERATION: AUTOMATIC

MAXIMUM CAPACITY: UP TO 87 GPM

DISCHARGE PIPE SIZE: 2" NPT

MAXIMUM SOLIDS HANDLING SIZE: 3/4"

MAXIMUM HEAD: UP TO 90'

MAXIMUM LIQUID TEMPERATURE: 120°F

CAPACITY: 87 GPM

HEADS: 90 FEET

TEMPERATURE: 120°F

RPM: 3450

AMP DRAW (full load): 12.1

SHIPPING WEIGHT: 70.0 LBS

SHIPPING DIMENSIONS: LENGTH: 14 In / WIDTH: 12 In / HEIGHT: 24 In

MATERIALS / CONSTRUCTION DATA:

BODY CONSTRUCTION: CAST IRON

IMPELLER CONSTRUCTION: ENGINEERED THERMOPLASTIC 

ELECTRICAL/MOTOR DATA:

HORSEPOWER: 1

VOLTAGE: 208-230V (1ø) 

MOTOR: OIL FILLED WITH AUTOMATIC RESET THERMAL OVERLOAD

CORD LENGTH: 20'; TYPE SJTW / STW-A

 KEY FEATURES:

GENERAL DATA:

MINIMUM SUMP DIAMETER: 24" FOR SIMPLEX / 30" FOR DUPLEX

MAXIMUM HEAD: 63'

DISCHARGE PIPE SIZE: 1.5" NPT

MAXIMUM SOLIDS HANDLING SIZE: 3/4"

MAXIMUM LIQUID TEMPERATURE: 120°F

PHASE: 1-PHASE

RPM: 1550

FULL LOAD AMP DRAW: 14.5 AMPS ON 115V

MOTOR: 1/2 HP WITH START CAPACITOR (SINGLE PHASE)

MAXIMUM (intermittent) LIQUID TEMPERATURE: 140 degrees F (60 degrees C)

AMP DRAW (full load): 12.0

DISCHARGE SIZE: 2" NPT

MAXIMUM CAPACITY: up to 64 GPM

SHIPPING WEIGHT: 33.0 LBS

SHIPPING DIMENSIONS: LENGTH: 12 In / WIDTH: 8 In / HEIGHT: 13 In

CONSTRUCTION/MATERIAL DATA:

FLOAT SWITCH: WIDE-ANGLE TETHERED STYLE

BODY CONSTRUCTION: CLASS 30 CAST IRON

IMPELLER MATERIAL: THERMOPLASTIC

IMPELLER CONSTRUCTION: TWO VANE SEMI-OPEN,THERMOPLASTIC

ELECTRICAL/MOTOR DATA:

POWER CORD: 20' SJTW

HORSEPOWER: 0.5 HP

VOLTAGE: AVAILABLE IN 115V

CORD LENGTH: 20'; TYPE SJTW

MOTOR: SHADED POLE WITH THERMAL OVERLOAD, OIL FILLED

 KEY FEATURES:

• Carbon/Ceramic Type 21 Shaft Seal
• Oil-Filled Motor with Automatic Reset Thermal Overload for Maximum Protection (single phase models)
• Upper and Lower Single Row Ball Bearing Construction
• Piggyback Plug Available for Easy Maintenance and Switch Replacement
• Submersible, Two-Vane, Semi-Open Cast Iron Impeller

GENERAL DATA:

MINIMUM SUMP DIAMETER: SIMPLEX: 18" / DUPLEX: 30"

DISCHARGE PIPE SIZE: 2" NPT (3" NPT optional)

MAXIMUM SOLIDS HANDLING SIZE: 2"

MAXIMUM LIQUID TEMPERATURE: 130 Degrees F (54 Degrees C)

MOTOR: SPLIT PHASE WITH THERMAL OVERLOAD PROTECTION

RPM: 1750

FULL LOAD AMPS: 12.0

SHIPPING WEIGHT: 58.0 LBS

SHIPPING DIMENSIONS: LENGTH: 14 In / WIDTH: 12 In / HEIGHT: 17 In

CONSTRUCTION/MATERIAL DATA:

BODY CONSTRUCTION: CLASS 30 CAST IRON

MAXIMUM HEAD: SKHS200: 75 ft. (22.9 m)

MAXIMUM CAPACITY: SKHS200: 175 GPM (11.0 LPS)

FLOW at 10' LIFT: 10' OF HEAD IS BELOW RECOMMENDED HEAD FOR THIS SERIES

IMPELLER CONSTRUCTION: CLASS 30 CAST IRON

ELECTRICAL/MOTOR DATA:

HORSEPOWER: AVAILABLE IN 1/2, 1, 1-1/2, AND 2 HP

SWITCH TYPE: WIDE-ANGLE TETHERED FLOAT SWITCH OR MANUAL OPERATION (MODEL DEPENDENT)

AMP DRAW (full load): MODEL AND VOLTAGE DEPENDENT - SEE SPEC SHEET FOR DETAILS

CORD LENGTH: 10' SJTW (20' OPTIONAL)

VOLTAGE: 115v or 230v in 1- or 3-PHASE (MODEL DEPENDENT)

 KEY FEATURES:

• Carbon/Ceramic Type 21 Mechanical Shaft Seal
• Oil-Filled Motor with Automatic Reset Thermal Overload Protection
• Upper and Lower Single-Row Ball Bearing Construction
• Piggyback Plug Available for Easy Maintenance and Switch Replacement
• Submersible, Two Vane, Semi-Open Cast Iron Impeller

 GENERAL DATA:

MAXIMUM HEAD: 28'

SOLIDS HANDLING: 2"

MAXIMUM CAPACITY: up to 120 GPM

MAXIMUM SOLIDS HANDLING SIZE: 2"

MINIMUM SUMP DIAMETER: 24" FOR SIMPLEX / 36" FOR DUPLEX

DISCHARGE SIZE: 2" NPT

PHASE: 1 PHASE

FULL LOAD AMP DRAW: 12 AMPS ON 115V

MOTOR: 6/10 HP / 1750 RPM

MAXIMUM (intermittent) LIQUID TEMP: 140 degrees F (60 degrees C)

SHIPPING WEIGHT: 65.0 LBS

SHIPPING DIMENSIONS: LENGTH: 14 In / WIDTH: 12 In / HEIGHT: 24 In

CONSTRUCTION/MATERIAL DATA:

BODY CONSTRUCTION: CLASS 30 CAST IRON

IMPELLER CONSTRUCTION: CLASS 30 CAST IRON, TWO VANE

ELECTRICAL/MOTOR DATA:

VOLTAGE: AVAILABLE IN 115V

HORSEPOWER: 0.6 HP

RPM: 1750

SWITCH: DIAPHRAGM PRESSURE SWITCH

POWER CORD: 20' OPTIONAL

MOTOR: SPLIT PHASE WITH THERMAL OVERLOAD PROTECTION

KEY FEATURES:

• Carbon/Ceramic Type 21 Mechanical Shaft Seal
• Oil-Filled Motor with Automatic Reset Thermal Overload for Maximum Protection (on single phase motors only)
• Upper and Lower Single-Row Ball Bearing Construction
• Piggyback Plug Available for Easy Maintenance and Switch Replacement

GENERAL DATA:

MAXIMUM HEAD: SP40: 25'

MAXIMUM CAPACITY: SP40: 140 GPM

MAXIMUM SOLIDS HANDLING SIZE: SP40: 1-1/4"

MAXIMUM WATER TEMPERATURE: 140 degrees F (60 degrees C)

MINIMUM SUMP DIAMETER: 18" FOR SIMPLEX / 30" FOR DUPLEX

DISCHARGE PIPE SIZE: SP40: 2" NPT / SP50: 2” NPT (3” opt.)

CONSTRUCTION/MATERIAL DATA:

BODY CONSTRUCTION: CLASS 30 CAST IRON

IMPELLER CONSTRUCTION: SP40 IS THERMOPLASTIC

ELECTRICAL/MOTOR DATA:

HORSEPOWER: AVAILABLE IN 4/10 HP

FLOW at 10' LIFT: SP40: 112 GPM

SWITCH TYPE: AVAILABLE WITH DIAPHRAGM PRESSURE SWITCH

CORD LENGTH: 20' SJTW

VOLTAGE: AVAILABLE IN 115v 1-PHASE

MOTOR: 4/10 HP PSC WITH THERMAL OVERLOAD PROTECTION

Threaded Pump Feet Support for Hydromatic HPG/HPGH